Level: Advanced 

When: Saturday, June 15, 2025

Time: 9:00am - 1:00pm 

Location:

***Attendees may not be accepted if course reaches capacity. Refunds will be issued for courses that are canceled due to low enrollment. (Travel reimbursements are excluded)

Advanced AC training class with focus on the impact of new components and chemicals. The change of refrigerant has changed the way we look at AC systems as well as how it should be diagnosed. The AC systems must perform better smaller components as well as increased complexity to make them as efficient as possible. This all leads up to the new Heat Pump systems on Electric Vehicles. The new components that we see in the normal AC systems are crucial in a Heat Pump system to make it operate efficiently. Best practices are changing nd if you do not change with it, it will cause massive failures in the AC/ Heat Pump system and cost the workshop a lot of money in warranty repairs.

• Diagnostics through pressure/ temperature ratio to make a more accurate diagnose.
• Trouble shooting on Electronic Controlled Valve compressor
• How to diagnose a micro-macro parallel condenser with the use of temperature and heat transfer measurementsComplex run-though of pressure settings and readings.
• Can I trust the pressure reading on my AC machine if it is a Variable displacement compressor system?
• How does the new electronic expansion valves work and how do you test them?
• What is the benefit of an IHX (Internal Heat Exchanger) compared to an older AC system without?
• Diagnosis of oil and how to check contamination.
• How to service an AC system with a new refrigerant such as R1234yf, R456A, etc.
• Does the products on an R134a system work with the new refrigerants?
• Will you keep the warranty if you use a new refrigerant on a R134a component?
• Groundbreaking new flushing procedure without removing any components from the AC system. Full flush and oil drain.FIRST TIME IN THE US
• Groundbreaking new method to replace ALL the oil without removing any components. FIRST TIME IN THE US.

LOCATION: 365 87th St, Daly City, CA 94015

TIME: 8:00AM - 5:00PM

***Attendees may not be accepted if course reaches capacity. Refunds will be issued for courses that are canceled due to low enrollment. (Travel reimbursements are excluded)

As more and more vehicle manufacturers choose ZF for their transmissions, shops can benefit and even potentially add simple services to their offerings by understanding the basics of the ZF 8HP transmission and how to diagnose common problems encountered in the repair shop and complaints from customers.  This in-depth class will take a deep dive into the function of the ZF 8HP transmission, and the best overhaul practices. The class will feature a classroom session, then participants will have the opportunity to practice what they have learned on a ZF 8HP transmission under the supervision of a ZF technical trainer.

After completing this training, the participant will be able to: 

· List internal components

· Explain the torque flow through the gears

· Describe the shift strategy

· Identify common failures

· Explain the oil change procedure

· Explain how to properly check the oil level

· Identify the differences between pressure regulators and solenoids

· Analyze transmission adaptation values and relearn procedures

· Review the disassembly and assembly process of the transmission

LOCATION: Pompano FL, Address To Be Determined

TIME: 8:00AM - 5:00PM

***Attendees may not be accepted if course reaches capacity. Refunds will be issued for courses that are canceled due to low enrollment. (Travel reimbursements are excluded)

As engineers have sought to make front wheel drive transaxles more efficient, they have used new concepts to help them reach the goals that have been set for more efficient drivelines and more forward gears. During this training, participants will first take a detailed look at the ZF 9HP to gain an understanding for how it is designed, and then take a deep dive into diagnostics. Participants will leave this training able to more effectively diagnose and repair ZF 9HP transaxles. 

After completing this training, the participant will be able to: 

• List internal components of the 9HP transmission  

• Identify the torque flow of all gears  

• Describe differences between pressure regulators and solenoids  

• Identify the different characteristics of pressure regulators  

• Differentiate between valve body types  

• Explain the shifting strategy of the ZF 9HP  

• Analyze transmission adaptation values and quick learn procedure  

• Explain an oil change service procedure for different manufacturers  

• Explain how to properly check the oil in the transmission  

• Describe the common failures of the ZF 9HP  

• Review the disassembly and assembly process of the transmission  

• Identify special tools needed for disassembly and assembly of the unit 

Location: 4105 Royal Dr NW suite 600, Kennesaw, GA 30144

4 Hour Course 8:00AM - 12:00PM (EST)

Steering and Suspension – Course Description

Maybe you have asked yourself, why does this car have so many control arms on it? Or, why does this European vehicle ride and handle so much differently than US domestic vehicles? As with many automotive systems, the steering and suspension systems on vehicles are constantly evolving. European automakers have been at the forefront of automotive technology, including the evolution of steering and suspension. For technicians, having a proper understanding of how these systems have changed and how they operate is critical in being able to properly diagnose modern vehicles.

This steering and suspension course, hosted by MEYLE, will be great for both beginner and intermediate technicians!

This course will cover technologies in both steering and suspension to give technicians a better understanding of common failures, diagnostics, tips and tricks, and best practices for repair.

• The participant can expect to learn:
• Advantages of Four Link Suspension systems
• Effects of “bump steer” on alignment
• Best practices for checking suspension systems
• Proper installation techniques
• Modern suspension technologies that improve ride quality and safety
• How Electric Power Steering works, and how it is similar to hydraulic steering systems
• Tips on when to replace electric rack and pinions and how they interact with other automotive systems

Limited to 12-Students per course!

Where: 4105 Royal Dr NW suite 600, Kennesaw, GA 30144

Online Webinar dates: (3 DAYS)

1. Jul 21, 2025 6PM - 8PM (EST)
2. Jul 22, 2025 6PM - 8PM (EST)
3. Jul 23, 2025 6PM - 8PM (EST)

In-Person Class Dates: (3 DAYS)

1. Friday, Jul 25, 2025 (1PM - 5PM) 
2. Saturday, Jul 26, 2025 (8AM - 5PM) 
3. Sunday, Jul 27, 2025 (8AM - 5PM) 

You MUST attend all in-person classes & all 3 webinars in order to receive your certification!

(***Attendees may not be accepted if course reaches capacity. Refunds will be issued for courses that are canceled due to low enrollment. (Travel reimbursements are excluded)

SSF PRO, in partnership with AC Training Academy, is proud to present our Industry’s first comprehensive and accredited Automotive High Voltage Certification Training Program.

This exclusive program is certified by Europe’s oldest and foremost Automotive Professional Body, The Institute of the Motor Industry, delivered by Senior Instructors trained and certified under European Regulation ECE-R100 as well as ASE.

Limited to 12-Students per course to ensure personal attention and in-depth training, this program combines 3 in-depth webinars plus 2.5 days of in-person hands-on instruction using custom-built simulators and equipment as well as actual electric vehicles. This course culminates with both a theoretical and practical exam where upon successful completion students will be officially registered with the IMI and can proceed directly to take ASE high voltage certification with no additional preparation.

 Online Live Webinar Topics:

1. Part 1: Electrical Basic Engineering         
2. Online Live Webinar Part 2: High Voltage Safety         
3. Online Live Webinar Part 3: High Voltage System Understanding
4. Online Live Webinar Part 4: High Voltage Disconnect and Diagnostics

 In-Person Training Topics:

1. Parallel and series electrical circuits.         
2. Function of resistors, diodes, transformers, rectifiers, and capacitors in HV systems         
3. Ohm’s law and the function of relays and transistors.         
4. Vehicle Intake process and safety measures.        
5. Determination of the state of the HV Battery.        
6. Four-wire Milliohm & Insulation test        
7. Diagnostic methods for EV        
8. Manufacturer disconnecting procedure and verify zero poten

Tools & Equipment Used for Training:

1. Custom-Built High Voltage Training Carts        
2. Color-Printed Student Guide plus Digital Reference Materials          Milliohm meters, Insulation Testers, Two Pole Voltage Testers, Multimeters, Oscilloscopes and Diagnostic Tool.        
3. High Voltage personal protection equipment (PPE) will be provided
4. Practical Exam will be delivered what includes score sheet and documentation         
5. Multiple choice questions for the theoretical Exam will be delivered. 

Theoretical and Practical Exams:

1. 45 minutes theoretical Exam (multiple choice)        
2. 30 minutes practical exam demonstrating and rated on the following tasks:         
3. Perform a certified disconnecting procedure.         
4. Diagnose the High Voltage system.         
5. Bonding and insulation faults must be found

LOCATION: Houston TX, Address To Be Determined

TIME: 8:00AM - 5:00PM

***Attendees may not be accepted if course reaches capacity. Refunds will be issued for courses that are canceled due to low enrollment. (Travel reimbursements are excluded)

With the electronification of the chassis, understanding of the OE design across multiple systems has become even more important in daily shop repairs. This class presents the correlation between those systems and electro-mechanical parts.  ADAS, electronic shock, Smart chassis, electronic steering are all new terms that shops need to be aware of and be able to properly diagnose. 4-wheel steer, another new but old term that is not introduced in the market once again. With the same basics started in our webinar class. ZF offers a more in depth and focused look into these topics during our hands-on training seminar.  The goal of this training is for a technician to leave with an understanding of how these changes influence the design of parts and knowledge of fault codes to properly diagnose daily needed repairs.

Time: 8 hours

After completing this training, the participant will be able to:

•          Describe common failures related to the electric steering system        
• Explain correlation between fault codes       
•   Describe collaboration between steering and transmission issues        
• List proper equipment for alignment and diagnostics      
•    Describe Smart Chassis      
•    Identify different driver assist functions and their operations        
• Understand active steering systems

Webinar (9:00AM PST, 12:00PM EST)

Please note that registration must be completed by 12:00 PM PST on the day prior to the webinar's start.

“As engineers have sought to make front wheel drive transaxles more efficient, they have used new concepts to help them reach the goals that have been set for more efficient drivelines and more forward gears. During this training, participants will first take a detailed look at the ZF 9HP to gain an understanding for how it is designed, and then take a deep dive into diagnostics. Participants will leave this training able to more effectively diagnose and repair ZF 9HP transaxles.” 

 After completing this training, the participant will be able to:  

• List internal components of the 9HP transmission   

• Identify the different characteristics of pressure regulators   

• Explain the shifting strategy of the ZF 9HP   

• Explain an oil change service procedure for different manufacturers   

• Explain how to properly check the oil in the transmission   

• Describe the common failures of the ZF 9HP   

• Review the disassembly and assembly process of the transmission   

• Identify special tools needed for disassembly and assembly of the unit 

Location: 1928 High St, Alameda, CA 94501

Limited to 12-Students per course!

Online Webinar dates: (3 DAYS)

1. August 18, 2025 6PM - 8PM (PST)
2. August 19, 2025 6PM - 8PM (PST)
3. August 20, 2025 6PM - 8PM (PST)

In-Person Class Dates: (3 DAYS)

1. Friday, August 21, 2025 (1PM - 5PM) 
2. Saturday, August 22, 2025 (8AM - 5PM) 
3. Sunday, August 23, 2025 (8AM - 5PM) 

You MUST attend all in-person classes & all 3 webinars in order to receive your certification!

(***Attendees may not be accepted if course reaches capacity. Refunds will be issued for courses that are canceled due to low enrollment. (Travel reimbursements are excluded)

SSF PRO, in partnership with AC Training Academy, is proud to present our Industry’s first comprehensive and accredited Automotive High Voltage Certification Training Program.

This exclusive program is certified by Europe’s oldest and foremost Automotive Professional Body, The Institute of the Motor Industry, delivered by Senior Instructors trained and certified under European Regulation ECE-R100 as well as ASE.

Limited to 12-Students per course to ensure personal attention and in-depth training, this program combines 3 in-depth webinars plus 2.5 days of in-person hands-on instruction using custom-built simulators and equipment as well as actual electric vehicles. This course culminates with both a theoretical and practical exam where upon successful completion students will be officially registered with the IMI and can proceed directly to take ASE high voltage certification with no additional preparation.

 Online Live Webinar Topics:

1. Part 1: Electrical Basic Engineering         
2. Online Live Webinar Part 2: High Voltage Safety         
3. Online Live Webinar Part 3: High Voltage System Understanding
4. Online Live Webinar Part 4: High Voltage Disconnect and Diagnostics

 In-Person Training Topics:

1. Parallel and series electrical circuits.         
2. Function of resistors, diodes, transformers, rectifiers, and capacitors in HV systems         
3. Ohm’s law and the function of relays and transistors.         
4. Vehicle Intake process and safety measures.        
5. Determination of the state of the HV Battery.        
6. Four-wire Milliohm & Insulation test        
7. Diagnostic methods for EV        
8. Manufacturer disconnecting procedure and verify zero poten

Tools & Equipment Used for Training:

1. Custom-Built High Voltage Training Carts        
2. Color-Printed Student Guide plus Digital Reference Materials          Milliohm meters, Insulation Testers, Two Pole Voltage Testers, Multimeters, Oscilloscopes and Diagnostic Tool.        
3. High Voltage personal protection equipment (PPE) will be provided
4. Practical Exam will be delivered what includes score sheet and documentation         
5. Multiple choice questions for the theoretical Exam will be delivered. 

Theoretical and Practical Exams:

1. 45 minutes theoretical Exam (multiple choice)        
2. 30 minutes practical exam demonstrating and rated on the following tasks:         
3. Perform a certified disconnecting procedure.         
4. Diagnose the High Voltage system.         
5. Bonding and insulation faults must be found